- 您现在的位置：买卖IC网 > Sheet目录303 > 844USB (B&K Precision)DEVICE PROGRAMMER USB INTERFACE
T06:
T11:<message>
Current serial number greater than limit
This record causes the serialization is stopped and warning or error
message is displayed in PG4UW software. The reason of turning
serialization off is the current serial number is greater then allowed
maximum ending serial number. This record can be used when -E
command line parameter is specified, it means no zero Last serial value
in dialog Serialization is specified.
Less important warning or message. The serialization will not be
interrupted.
Flowchart of device programming with custom-generator serialization
When Custom-generator serialization is used, it means, that before each device programming
is started, serialization engine calls serialization generator executable, to
generate serial .dat file. PG4UW serialization engine manages proper
command line parameters for calling of serialization generator. The data
from .dat file are immediately read to internal programmer buffer and used
as data for programming device. Also next serial number information
(record T02) is remembered in PG4UW.
Typical flowchart of device programming is following:
1. Start of programming batch
2. Device insertion test
3. Serialization sequence, consists from four steps:
call of serialization generator with proper command line parameters to generate
serialization .dat file
waiting for serialization .dat file to be available
reading of serialization .dat file data to programmer buffer (the data will be used for
programming device)
delete serialization .dat file after reading of data from it
4. Device programming
5. Device verification
6. Operation result check.
This is fully managed by PG4UW control program. Serialization generator does not
have to do any operation according to operation result. Control program will call
serialization generator with required command line parameters.
OK - PG4UW makes request for next serial number. Next serial number was read from
.dat file in step 3. Call of serialization generator will have next serial number specified in
command line.
ERROR - PG4UW does not make request for new serial number. Recent serial number
will be used for next device. Next call of serialization generator will have recent serial
number specified in command line.
7. Repeat programming with next device?
Yes
No
goto step 2.
continue at step 8.
8. End of programming batch
Notes:
In case of error programming result, recent serial number is used, but generator will be
called at step 3. anyway, even if the same number is used as for previously
programmed device.
86
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
84702-0008
CONN RECEPT ETHERNET 8-8 PNL MNT
848A
MEMORY PROGRAMMER PARALLEL INTER
85506-0001
CONN MOD JACK VERT 8-8 HI-SPEED
85507-0001
CONN MOD JACK VERT 8-8 SHIELDED
85508-0001
CONN MOD JACK VERT 8-8 SHIELDED
85508-5001
CONN MOD JACK 8POS T/H HI SPEED
85511-0001
CONN MOD JACK VERT 8-8 HI-SPEED
862015-1
6 POS RECEPTACLE
相关代理商/技术参数
845
功能描述:程序设计器 - 基于通用和内存 REORD 615-865 UNIV. WITH SOFTWARE
RoHS:否 制造商:Xeltek 产品:Universal Device Programmers 工具用于评估:EPROM, Parallel/Serial EEPROM, FPGA, PROM, Flash, BPROM, MCUs, PLD Devices 接口类型:Parallel, USB 工作电源电压:90 VAC to 250 VAC
845 1 1/2"X15YD
功能描述:SCOTCH BOOK TAPE 845 1-1/2 IN X 制造商:3m 系列:* 零件状态:在售 标准包装:24
845 3"X15YD
功能描述:SCOTCH BOOK TAPE 845 3 IN X 15 Y 制造商:3m 系列:* 零件状态:在售 标准包装:12
845 4"X15YD
功能描述:SCOTCH BOOK TAPE 845 4 IN X 15 Y 制造商:3m 系列:* 零件状态:在售 标准包装:8
845 PRO4
制造商:Micro-Star International 功能描述:845 P4 S478 SDRAM LAN - Bulk
845 PRO4-L
制造商:Micro-Star International 功能描述:845 P4 SKT478 ATX SDRAM - Bulk
845 ULTRA
制造商:Micro-Star International 功能描述:845 SKT-478 P4 DDR ATX AUD - Bulk
845 ULTRA-DF
制造商:Micro-Star International 功能描述:845 SKT-478 P4 DDR ATX AUD - Bulk